首页 > 产品

产品

UCD3138数字电动工具 字幕
UCD3138数字电动工具
课程时长:36:21
视频集数:6
标签: UCD3138 GUI
This video explains the software tools that TI provides for UCD3k code development and includes an introduction to the UCD3k open loop board, which is required to complete the tutorials.
UCD3138数字PWM(DPWM)模块 字幕
UCD3138数字PWM(DPWM)模块
课程时长:25:28
视频集数:6
标签: UCD3138 PWM DPWM
This video introduces the three digital power peripherals, focusing on the DPWM module.
UCD3138数字滤波器模块 字幕
UCD3138数字滤波器模块
课程时长:43:17
视频集数:7
标签: UCD313 8数字滤波器
This training introduces the digital filter module, which is used as the compensator in the closed loop system provided by the UCD3138 family of devices. This module is designed to replace the analog compensation network employed in power supplies based on analog power management controller ICs.
UCD3138模拟前端(AFE)模块 字幕
UCD3138模拟前端(AFE)模块
课程时长:20:18
视频集数:7
标签: UCD3138 AFE
This video introduces the front end module and discusses its basic operation.
将JTAG与UCD3138配合使用 字幕
将JTAG与UCD3138配合使用
课程时长:53:09
视频集数:12
标签: JTAG UCD3138
This video introduces the hardware and software required to communicate with the UCD3138 series of digital power controllers via JTAG. Modifications that may need to be made to the open loop boards to enable JTAG are shown as well.
为JTAG通信设置UCD3138 字幕
为JTAG通信设置UCD3138
课程时长:2:26
视频集数:1
标签: JTAG UCD3138
On the UCD3138, JTAG comms are disabled by default by the ROM code that executes on device startup. This video outlines the steps required to enable comms on the UCD3138 when the part is in ROM mode. Please note that this step applies only to the UCD3138 and is NOT required for the following devices:- UCD3138A- UCD3138064- UCD3138064A- UCD3138A64- UCD3138128- UCD3138128A
在UCD3138系列上启用JTAG通信 字幕
在UCD3138系列上启用JTAG通信
课程时长:3:38
视频集数:1
标签: UCD3138 JTAG
On startup, checksums tests are executed by the boot ROM code to verify the integrity of the program flash contents. If any of these tests pass, JTAG comms are disabled by the boot ROM code before control is relinquished to the firmware in program flash. We show the line of code that you need to insert in your firmware to re-enable JTAG comms. The tutorial also shows the modification available via PMBus to the IOMUX register on the UCD device to re-enable JTAG comms, of course to make this modification, the firmware needs to support PMBus.
什么是静电放电(ESD)? 字幕
什么是静电放电(ESD)?
课程时长:5:03
视频集数:1
标签: 静电放电 ESD
This video provides an overview of ESD including the events that cause electrostatic discharge and the sources of it. We will also discuss applications requiring protection from ESD strikes.
什么是瞬态电压抑制器(TVS)二极管? 字幕
什么是瞬态电压抑制器(TVS)二极管?
课程时长:5:21
视频集数:1
标签: 瞬态电压抑制器 TVS二极管
This video provides a brief overview of transient voltage suppressor (TVS) diodes and why they are necessary for protecting integrated circuits.
DesignDRIVE位置管理器SIN / COS解决方案简介 字幕
DesignDRIVE位置管理器SIN / COS解决方案简介
课程时长:6:04
视频集数:1
标签: MCU C2000
An overview of the DesignDRIVE Position Manager solution for SIN/COS encoder sensors is presented.
基于SimpleLink的超低功耗无线MCU平台CC1310DK 字幕
基于SimpleLink的超低功耗无线MCU平台CC1310DK
课程时长:2:25
视频集数:1
标签: SimpleLink MCU CC1310DK
The CC1310 Development Kit includes features such as an LCD screen, buttons, sensors, breakout pins, and an on-board debugger. Using the CC1310DK, developing and debugging is made easy for everyone!
new
关闭广告